2021+ Bronco B Pillar Protection
These printed B pillar overlay photos do not do them justice. In person these look great! I can't believe we didn't make them sooner. They blend in really well with our printed series fender overlays as well.
It's easy to install and can cover up minor imperfections and discolorations in the B pillar.
Fits ALL 2/4 door 2021+ Broncos. Matte finish.
2 pieces:
- Left Pillar
- Right Pillar
Customization
While StickerFab caters to a large number of people, it is still possible to customize some orders. Ideas that have broad appeal are the best! However, if you have some art work, we may be able to do a special print just for you.
- Military Themed
- Patriotic
- Other organizations
Please refrain from submitting trademarked content unless you have the rights to it. We are located in Fort Myers, FL if you are interested in helping us create custom templates for other vehicles or trim levels.
Use our contact form to get in touch with us.
INSTALLATION
Use the following video and written instructions to complete the install. NOTE: All topo vinyls are shipped in tubes to prevent damage. Prior to install, lay out all of these items and make sure they are flat prior to install.
You will want to do this in 80-85 degree weather ideally. Stay in the shade unless it is a little on the cool side.
Recommended items:
- This Kit (overlays + 3M promoter stick)
- Optional Squegee
- Microfiber
- Detailer spray to prep the area (without wax)
- Alcohol wipe
- Optional Heat gun or hair dryer
We recommend doing this after a fresh car wash. Re-clean the application area to prepare it for installation. Just use a wax free detailing spray if your vehicle is not too dirty. Do not forget to clean the edges of the B pillar. Also wash your hands. You do not want to get dirt stuck to the adhesive side of the material. You can use an alcohol wipe on the edges. Note if the wipe is still dirty after use and use more if needed. Allow area to dry.
Prep both sides. Then use the 3M adhesive promoter on the edges of the pillar. It dries out quickly so you need to do both sides within a few minutes. The promoter is required as the pillar is textured and the curved edges need this preparation for the vinyl to stick properly. Allow time to dry.
Do a DRY INSTALL, but be careful not to crease the vinyl. This material is pretty forgiving if installed under the right temperatures. Align the vinyl along the top and lead edge. Then push out the air carefully as to prevent creasing. You can also use a combination of your hands and the felt tip squeegee.
The adhesive reacts to PRESSSURE and HEAT.
Customer Reviews
I wanted these but Antimatter Blue wasn't available. I reached out on the messaging portal to ask what color would look good w my paint. Within 15 minutes they got back to me and said they added it for me. I was so stoked. These went on super easy and are a subtle change. Not flashy at all, just the right hit for the exterior. When you line them up, try to center from top to bottom but error to having the excess on the front seat side. There is a little more room to wrap around on the front side. If you do that, it looks damn near like it's a full imprinted plastic piece.
Very good quality material is very forgiving was able to install & reinstall till I got the right look
Thought it was plastic. It’s vinyl wrap. Not a clean fit. The edges ruffle a bit and no way to keep it down. The rest looks very nice though. I realize it was my fault for not reading the description more thoroughly.
Hello,
Sorry to hear that. Checking the weather in your area, it doesn't seem like it got to the recommended temperature in the video.
Were you able to watch it? We believe it had some helpful content.
Thanks
Items took longer than i expected nut upon arrival they look great once on the truck it looks even better. Great job thank you ..
These look great! Such a simple addition to make my Bronco stand out from the others
I saw the announcement in Bronco6g and said “why not”. So I ordered. Came quickly. The suscriptions describes both wet and dry install but the new install video recommends dry. I’d never done a dry install. It actually wasn’t too bad. The vinyl is very forgiving. I cleaned thoroughly and installed. Used a bit of heat gun because, hey, I rarely see 75-85F in Berkeley, CA.
Product looks great! It’s a small thing but kinda cool. And really those B-pillars don’t clean easily. Just like the fender flares. They stain easily. (Honestly I don’t really care but many do.) My daughter walked home from school and saw the Bronco in the driveway as I was cleaning up post install and said “wait I’ve never noticed that…” Told her it’s new and she rolled her eyes. Heh. What to expect from a high schooler?
I like them. Don’t know how long the edges will hold but we shall see. A small price for a little Bronco whimsy!
