Perforated see-through vinyl that acts like tint — blocks ~50% of light, cuts heat, and wraps your rear glass in trail-inspired topographic artwork.
See Out, Style Up
Unlike our solid version, the V3 uses a perforated material — it behaves a lot like window tint. From the outside you get the full topographic map look with roughly 50% light blocking; from the inside you can still see through the glass. It's the best of both worlds: privacy and heat reduction without fully blacking out the window.
The perforated surface makes a great canvas for our topographic contour design, giving the rear glass a rugged, adventure-ready finish that matches an off-road build.
Built to Last
Perforated tint-style material — blocks ~50% light, see-through from inside
TruProtect UV-resistant laminate — guards the print against fading and the elements
TruPrint quality — authentic Roland inks and printers for saturated color
Made in the USA — printed and cut in-house
Precision fit — cut for the 2024+ Land Cruiser rear glass, sold as a matched left/right pair
Multiple Finishes
Match your build. Available in Heritage Blue, Area 51, Carbonized Gray, Cyber Orange, Desert Sand, Race Red, Solar Orange, Urban Green, Velocity Blue, White, and Mustard Yellow.
Need a color you don't see? Reach out through our contact form — we can often print custom finishes.
⚠️ Important — Perforated Material Handles Differently
This material installs like our solid printed window vinyl, but it stretches more easily and is more delicate. Do NOT use a squeegee — press it down with your fingers only. Install in the shade in 70°F or warmer weather. If you overstretch it, pull it back up or trim. Do not use anything rough to install or clean the surface.
V3 Install Walkthrough
Watch the V3-specific install video for this exact perforated overlay on the 2024+ Land Cruiser. Do a wet install in 70°F+ weather, out of direct sunlight, and press the vinyl down with your fingers — no squeegee needed.
Full Install Steps
Clean the glass thoroughly with glass cleaner and a microfiber — the surface must be free of wax and grime.
Mix a wet-install solution: one drop of dish or hand soap in a cup of water (or use our StickerFab Installation Fluid).
Spray the vinyl so it doesn't grab on first contact, then slide it into position. There's a border around the edge for easier alignment around the rubber gaskets.
Press down with your fingers — do NOT use a squeegee. Work slowly so you don't overstretch the perforated material.
Work in the shade in 70°F+ weather so the vinyl doesn't heat up too fast. Even out the small gaps at the ends. A heat gun or hair dryer on low can help conform edges.
Everything you need: our 3-item install kit (microfiber, installation fluid, squeegee — use the squeegee only for other vinyls, not this perforated material).
⚙️ Install Tip — Fingers, Not Force
A wet install lets you reposition before it sets. Press with your fingers, keep it out of the sun, and take your time — the perforated material rewards patience. We filmed a long, unedited install so you can follow every step; fast-forward or rewind as needed.
FAQ
What's the difference from the Solid version? This V3 is perforated — it acts like tint, blocking ~50% of light while staying see-through from the inside. The Solid version fully blocks the view.
Can I see out of the windows? Yes — from inside you can still see through it. From outside it reads as a solid topographic design.
Does it fit my Land Cruiser? Yes — it's cut for ALL 2024+ Toyota Land Cruisers, sold as a driver + passenger pair.
Do I need a squeegee? No — press it down with your fingers only. A squeegee can damage the perforated surface.
Will it damage my glass? No. It applies with a wet install and removes cleanly without harming the glass.
Can I get a custom color? Often, yes. Use our contact form and we'll let you know what's possible.
StickerFab is an independent brand and is not affiliated with, sponsored by, or endorsed by Toyota Motor Corporation. All vehicle names are used for fitment reference only.
