ORACLE Flush Style LED Tail Lights - 2021+ Ford Bronco
The ORACLE Lightingflush-style LED Tail Lights transform the rear of the 2021+ Ford Bronco with a low-profile design that sits tight to the body panel - protruding significantly less than the factory tail lights. That difference matters on tight trails where protruding factory tails get caught on rocks and brush. The flush wrap-around design also means the signature perimeter lighting is visible from any rear angle.
At the rear, 60W high-powered LED reverse lights provide over 8,000 lumens of illumination - essentially a pair of LED light bars built into each tail light. This is a major upgrade over the factory reverse light output.
Available in four configurations depending on your Bronco's factory tail light setup. Broncos with factory halogen tail lights get a plug-and-play install. Broncos with factory LED tail lights need the -023 series and require a quick FORScan programming step to configure the BdyCM module - instructions included.
Which Version Do I Need?
These lights are available in two part number series depending on whether your Bronco came from the factory with halogen or LED tail lights:
5892-504 / 5892-504-T - For Broncos with factory HALOGEN tail lights. Plug-and-play install, no programming required.
5892-023 / 5892-023-T - For Broncos with factory LED tail lights. Requires a FORScan BdyCM module configuration step after install.
How to tell which you have: Check the window sticker or the door jamb sticker for "LED Tail Lamps." You can also look at the lights themselves - factory LED tail lights have a more complex multi-element light pattern compared to the simple single-bulb halogen units. If you are unsure, the halogen version (5892-504 series) is the more common fitment across most Bronco trim levels.
60W LED Reverse Lights
Each tail light unit houses a 60W high-powered LED reverse light array that produces over 8,000 lumens of rear-facing illumination. That is essentially a pair of LED light bars integrated directly into the tail light housing. Whether you are backing into a campsite at night or navigating a dark trail, the reverse light output is a massive step up from the factory incandescent or LED reverse bulbs.
Signature Perimeter Lighting
The ORACLE flush mount design features a signature perimeter LED light strip that wraps around the outer edge of the tail light housing - following the contour of the vehicle body. Because the housing sits flush and wraps around the body panel, this perimeter lighting is visible from any rear angle, not just directly behind the vehicle. It gives the Bronco a distinctive, unmistakable look day or night.
Trail Protection
Factory Bronco tail lights protrude noticeably from the body. On tight trails - squeezing past trees, boulders, or brush - those protruding tails take the hits. The ORACLE flush mount design sits dramatically closer to the body panel, reducing the exposure and protecting the lights from trail damage. Less protrusion means less to snag, less to crack, and less to replace.
FORScan Programming (LED Broncos Only)
If your Bronco came with factory LED tail lights, you will need to complete a one-time FORScan programming step after installation. This is done through the BdyCM Module Configuration (NOT the AsBuilt Module). The settings required are:
Rear LED Turn Outage: Disabled
Right Rear Stop and Position Lamp Usage: Stop and Turn
Right Rear Turn Lamp Usage: Not Used
Left Rear Stop and Position Lamp Usage: Stop and Turn
Left Rear Turn Lamp Usage: Not Used
FORScan is free software available at forscan.org. An OBD2 adapter is required. This is a straightforward process and full instructions are included with the lights.
Compatible Accessories
Flush Mount Tail Light Overlays - Dark smoke and other finishes available, designed specifically for the ORACLE flush mount housings.
21 Offroad Magic Reverse Harness - Taps into the Bronco's reverse signal via the auxiliary switch bank. Fully compatible with the ORACLE flush mount lights.
How do I know if my Bronco has halogen or LED tail lights? Check the order sticker in the door jamb for "LED Tail Lamps" or look at the tail lights directly - LED units have a more complex multi-element light pattern. If you are unsure, the halogen version (5892-504 series) is the more common fitment.
Does the LED version (5892-023) require FORScan? Yes - factory LED Broncos need a BdyCM module configuration change after installation. The exact settings are listed in the FORScan section above. Instructions are also included with the lights.
Will these fit my Bronco Raptor? No - these do not fit the Bronco Raptor or Bronco Sport. They fit all other 2021+ Ford Bronco trims.
Are overlays available for these lights? Yes - flush mount overlays in dark smoke and other finishes are available separately and are designed specifically for these housings.
Are these compatible with the 21 Offroad Magic Reverse Harness? Yes - fully compatible. The Magic Reverse Harness works seamlessly with the ORACLE flush mount lights.
Fitment
2021-2025 Ford Bronco with factory halogen tail lights - use 5892-504 series (plug-and-play)
2021-2025 Ford Bronco with factory LED tail lights - use 5892-023 series (requires FORScan)
