Diode Dynamics D-Switch 8-Channel Switch Panel
Program and control your lights, compressors and 12V accessories from one solid-state system, with a controller, a phone app and your infotainment screen.
Dynamic Channel Assignment
On a typical switch panel, button 1 is permanently tied to output 1. On the D-Switch you can group several output channels under a single button, so one press turns on your ditch lights, rock lights and dash LEDs together.
You can also give one output different patterns on different buttons, for example one button for flashing and another for full power. Reprogram it any time with no rewiring.
|
 |
 |
The 9th Button: A Dedicated Backlight Bus
Most 8-button panels stop at 8 outputs. The D-Switch adds a 9th button wired to a dedicated backlight bus bar, so you can power all of your backlit accessories with one press.
That leaves your 8 main outputs free for the gear that actually draws current.
|
Control It Three Ways
Use the physical controller, the Bluetooth app (iOS and Android) or Apple CarPlay and Android Auto on your head unit.
OEM Signal Integration
Four trigger wires plus an ignition wire let the D-Switch work like factory equipment. The ignition wire powers the controller when the vehicle starts and shuts it down when you turn it off.
Trigger wires connect to signals like high beams, fog lights or reverse lights to activate outputs automatically. The Night Mode wire adjusts output settings and controller brightness for low-light driving.
|
 |
 |
Two Mounting Options Included
Mount the controller flush in a panel or use the universal mounting bracket that comes in the box. Both options are included, so you can pick whatever suits your dash or console.
|
Watch the D-Switch
What's in the Box
- Switch panel hub (1) and controller (1)
- Controller universal mounting bracket (1)
- Controller wiring harness
- Trigger wires and Night Mode wiring harness
- 3 ft 4AWG battery cable and 3 ft 4AWG ground cable
- Button sticker sheets (2)
- Installation hardware
- Installation and programming guide
Want to read the guide first? D-Switch Installation Guide (PDF)
Specifications
-
Channels: 8 output channels + 1 dedicated backlight channel
-
Output power: four 15A and four 30A channels, plus the backlight channel
-
Max total current: 125A
-
Operating voltage: 9–16V DC
-
Operating temperature: -40°F to 250°F
-
Weatherproof rating: IP67 (hub and controller; wiring terminals excluded)
-
Connectivity: Bluetooth (iOS and Android app), Apple CarPlay, Android Auto
-
Trigger inputs: ignition, high beam, fog, reverse, Night Mode
-
Controller size: 5.06 x 2.65 x 0.45 in | Hub size: 8.33 x 6.26 x 1.79 in
-
Origin: engineered and assembled in the USA
-
Warranty: 3-year limited
-
Part number: DD8373 (our SKU DIODD8373)
This Part Fits
- Universal: works on any 12V DC vehicle, not vehicle-specific
- Popular on the 2018+ Jeep Wrangler, 2021+ Ford Bronco, 2024+ Toyota Tacoma, 2025+ Toyota 4Runner and 2024+ Toyota Land Cruiser
- Wiring uses the included battery and ground cables; a 7 ft extended battery cable is available from the manufacturer if you need to mount further from the battery
Complete the Build
FAQ
Does this work with any vehicle? Yes. The D-Switch works with any 12V DC vehicle, so it is not vehicle-specific. Trucks, Jeeps, Broncos, Tacomas, 4Runners and overlanders all use it. |
Do I need the app after setup? No. Programming is stored on the hub. Once configured over Bluetooth, daily use runs from the controller or your infotainment screen. |
What is the difference between the 15A and 30A channels? The four 15A outputs suit LED pods, light bars and most 12V accessories. The four 30A outputs are for high-draw gear like air compressors or large arrays of rock lights. |
Is it waterproof? The hub and controller are rated IP67. Wiring terminals are not part of that rating, so route and seal them carefully during install. |
Can I control it while driving? Yes. Mount the controller within reach or use Apple CarPlay or Android Auto to run all your channels from the dash. |
Will it turn on and off with the vehicle? Yes. Wire the ignition input to an ignition source and the controller powers on and off with the vehicle. You can still power it on manually with the ignition off. |
Can I trigger outputs automatically? Yes. Trigger wires connect to signals like high beams, fog lights or reverse lights so you can set outputs to turn on automatically. |
What is the warranty? The D-Switch has a 3-year limited warranty. Return terms for this product may differ from StickerFab-branded items - see our refund policy or email info@stickerfab.com before you order. |