The 2024 Land Cruiser (LC250) has the kind of rear quarter window that's just begging for a custom touch. Big, flat, perfectly visible — and from the factory, totally blank. Our topographic window overlay was one of the first products we built specifically for the LC250, and the V3 version is the cleanest, sharpest, easiest-installing version yet.

What Is the Topographic Window Overlay?

It's a precision-cut vinyl overlay that applies to the rear quarter windows of the 2024+ Toyota Land Cruiser. The design is a topographic map pattern — flowing contour lines that look like a section of a USGS quad sheet — that gives your LC250 an instant outdoorsy, expedition-ready vibe without committing to anything permanent.

From a few feet away, it looks like factory tinted glass with a subtle pattern etched in. Lean in and you see the detail. Roll up to a trailhead and watch other LC owners stare.

Why It's One of Our Most Popular LC250 Products

• Unique to the platform. You won't see this on every other Land Cruiser at the meet.
• Premium cast vinyl. 7+ year outdoor durability, fade-resistant, won't peel at the edges.
• Pre-cut to exact spec. No trimming, no guessing — drops right onto the glass.
• Removable. Pulls clean if you ever want to change it up.
• Made in the USA. Printed and cut at our Florida shop.

V3 Install Guide: Topo Rear Window Overlay

The V3 release dialed in the fitment and made the install dramatically easier. Watch the video above for the full walkthrough, but here's the quick reference.

What You'll Need

• Spray bottle with water + a couple drops of dish soap (slip solution)
• A squeegee or hard plastic card
• Microfiber towel
• Isopropyl alcohol (70%+) for prep
• 15 minutes per side

Step-by-Step

1. Clean the glass thoroughly. Wipe down with isopropyl alcohol and let it flash off. Any dust or oil here will show up as bubbles later.
2. Spray the glass with slip solution. Don't be shy — soak it. The soap lets the vinyl float so you can position it.
3. Peel the backing. Spray the adhesive side of the overlay with slip solution as you peel.
4. Position the overlay. Line it up using the window edges as reference. The slip solution gives you 30+ seconds to slide it into place.
5. Squeegee from the center outward. Use firm, overlapping strokes to push the water and air bubbles out toward the edges.
6. Wipe and inspect. Dry with a microfiber and check for any remaining bubbles. Small ones will work themselves out in 24-48 hours.
7. Repeat on the other side.

Pro Tips

• Install indoors or in shade — direct sun makes the adhesive grab too fast.
• Don't wash the vehicle for 48 hours after install.
• If you get a stubborn bubble, prick it with a fine pin and squeegee from the opposite side.

Pair It With the Rest of Our LC250 Lineup

The topo overlay looks amazing on its own, but it really sings when paired with our other LC250 products — dashboard accent overlays, gauge trim kits, badge blackouts, and door sill protectors. We've built one of the most complete custom-overlay catalogs for the 2024 Land Cruiser anywhere, and it keeps growing.

Set Your LC250 Apart

The 2024 Land Cruiser is a special truck. The topographic window overlay is one of those little touches that takes it from impressive to unmistakable. Easy to install, easy to live with, easy to love.

Shop the topographic window overlay and our full 2024 Land Cruiser collection →

Designed and made in Florida by a veteran-owned shop. Backed by 4,600+ five-star reviews. Premium vinyl, premium fitment, premium results.

The fog light overlay is one of the easiest, highest-impact mods you can do to a 4th gen Tacoma. No tools beyond what's already in your kitchen drawer, no permanent changes, and the whole job takes about 15 minutes per side once you've done it.

This is the install guide we wish came in the box. (We do include directions — but a real walkthrough hits different.)

What You'll Need

• Your 2024 Tacoma fog light overlays
• Microfiber towel
• Isopropyl alcohol (70% or higher)
• Spray bottle with water + 1 drop of dish soap (for the wet method)
• Squeegee or old credit card wrapped in microfiber
• Heat gun or hair dryer (optional but recommended)
• Patience and a shaded spot

Step 1: Prep the Surface (Don't Skip This)

This is where 90% of bad installs go wrong. Your fog light bezels look clean, but they aren't. Road grime, wax residue, and microscopic dirt will all sabotage adhesion.

1. Wash the front of the truck with soap and water
2. Dry the fog light area completely
3. Wipe each bezel down with isopropyl alcohol on a microfiber
4. Let it flash off for 60 seconds — no shortcuts

Pro tip: don't install in direct sun or below 50°F. The vinyl adhesive is happiest between 65–85°F. A shaded driveway or open garage is ideal.

Step 2: Dry-Fit the Overlay

Before you peel anything, hold the overlay up to the bezel with the backing still on. Get a feel for how it lines up with the edges. Our overlays are precision cut for the 2024 Tacoma, so it should drop right into place — but knowing where the edges sit before you start saves a lot of stress.

Step 3: Choose Wet or Dry Method

Dry Method (Faster, Less Forgiving)

Best for: small, simple overlays and people who've installed vinyl before.

1. Peel back about 1/3 of the backing
2. Line up the top edge carefully and press down
3. Slowly pull the rest of the backing while squeegeeing from center to edges
4. Press firmly along all edges

Once it's down, it's down. No repositioning.

Wet Method (Slower, Mistake-Proof)

Best for: first-timers, larger overlays, or hot days when adhesive grabs too fast.

1. Mix water with one drop of dish soap in a spray bottle
2. Mist the fog light bezel lightly
3. Peel the backing fully off the overlay
4. Mist the adhesive side too
5. Place the overlay — it'll float and slide so you can position it perfectly
6. Squeegee from the center outward to push out water and air
7. Press the edges firmly

The vinyl will lock down once the water evaporates (usually 24 hours).

Step 4: Heat-Set the Edges

This is the step most people skip — and it's the difference between an overlay that lasts five years and one that peels in six months.

Run a heat gun (low setting) or hair dryer along all edges of the overlay for about 10–15 seconds per section. You're not trying to melt it — just warm the adhesive enough that it conforms perfectly to the bezel's curves.

Then press one more time with a microfiber-wrapped squeegee.

Step 5: Walk Away

Don't wash the truck for 48 hours. Don't pressure wash that area for a week. Let the adhesive fully cure.

Common Install Mistakes (And How to Fix Them)

Bubbles under the vinyl

Small bubbles will usually self-release within a few days. For bigger ones, prick with a fine needle at the edge, push the air toward the hole, then heat and press.

Edge lifting after a wash

Almost always means the surface wasn't clean enough during prep. Lift the edge, clean with alcohol, reheat, and press back down.

Overlay misaligned

If you used the wet method, you have a few minutes to slide it. If you went dry and it's off, gently lift slowly with a heat gun warming the adhesive.

How Long Will It Last?

Our vinyl is rated for 5–7 years of outdoor exposure. Florida sun, Pacific Northwest rain, Midwest road salt — it holds up. And if you ever want to remove it, a heat gun and a few minutes is all it takes. No paint damage, no residue.

Ready to Install?

Grab your set, set aside half an hour on a Saturday morning, and your front end is going to look noticeably better by lunch.

Shop 2024 Tacoma Fog Light Overlays →